Hakko FM-205 120W Desoldering / Soldering Station

Hakko FM-205 120W Desoldering / Soldering Station

The Hakko FM-205 Digital Desoldering Tool is very similar to the Hakko FM-204 except that it uses compressed air to generate the vacuum rather than an internal pump. This provides for slightly higher vacuum pressure, increased suction flow, and a lower station cost.

Requires Shop Air.
Digital Temperature Control.
Temperature range 200 – 450°C (400 – 840°F)
Temperature accuracy ±15°C
Uses composite nozzles for improved thermal performance.
Quick-change composite nozzles (N3 series).
Uses low cost disposable filter cartridges.
Can be used as a soldering station with a Hakko FM2027 connector.
Gun or Pencil-style desoldering handpiece.
Less prone to clogging as compared to older desoldering stations when used on lead free applications.
Includes low temperature alarm, sleep mode functionality & auto power off.

Included:

FM2024-02 desoldering handpiece
A1511 filter pipe assembly
B2972 control card
FH200-05 sleep stand iron holder
599B-02 wire sponge tip cleaner
B2873 cleaning drill
B2876 nozzle remover
B2300 ESD safe heat resistant pad
A1514 ceramic paper filters

Kiesub Electronics is a leading distributor of Hakko soldering equipment. Located in Las Vegas, we stock a wide variety of Hakko soldering stations, desoldering and rework stations, solder tips, desolder nozzles, analog and digital soldering stations, soldering irons and guns, solder and solder paste, and many other soldering accessories.

Hakko FM-206-DSS 3-Port Rework Station

FREE UPS GROUND SHIPPING

The Hakko FM206-DSS configuration contains:

(1) FM-2024 desoldering tool (FM2024-42 Kit)
(2) FM-2027 soldering irons (FM2027-06 Kit)
• FM206-55 station is included.

• Graphic User Interface for easy setup and operation
• 3 simultaneous powered ports
• Self-contained pump for vacuum and air flow
• Digital airflow indicator
• Configurable display in °C or °F
• High performance hot air handpiece ramps up to max temp in < 20 secs
• Capable of hot air rework of 0201, 01005 and up to 10x10mm QFNs
• Meets or exceeds ANSI J-STD-001
• Manual or Automatic profile for hot air
• Auto shutoff with sleep function
• Passcode protected
• Security lock to protect against theft or unauthorized re-location
• Integrates with the Hakko FR-830 and FR-870 Preheaters
• Low cost composite hot air nozzles
• Desoldering delay timer
• Optional footswitch for pump operation
• Option for external gas supply for hot air
• ESD safe by design

NOTE: Tips and Nozzles are NOT included with station or any configuration

Click here for N3 nozzles for the included FM2024 Desoldering Tool

Click here for T15 tips for the included FM2027 Soldering Irons

Hakko FM-206-STA 3-Port Rework Station

Hakko FM-206-STA 3-Port Rework Station

Free Ground Shipping!

FM206-STA configuration:

FM-206 Rework Station with FM-2022 Parallel Remover, FM-2029 Hot Air Handpiece, and FM-2027 Soldering Iron.

Hakko FM2024-21 Desoldering Module Conversion Kit with Sleep Holder

Hakko FM2024-21 Desoldering Module Conversion Kit with Sleep Holder

Hakko FM2024-21 Desoldering Module Conversion Kit features:

The Hakko FM-2024 Desoldering Module extends the versatility of the award winning Hakko FM-202 or thenew FM-203 Soldering Station giving you a complete soldering and desoldering solution, in one modular station.

Building on Hakko’s revolutionary composite tip technology, the desoldering nozzle/tip heater cartridge assembly offers a one-step, quick-change design with fast thermal recovery; the enlarged throat and shortened nozzle design is virtually non-cloggable, making it ideal for NO LEAD applications; and its slender body enables it to reach those difficult-to-reach component pads on densely populated boards.

The Hakko FM-2024 also features an extremely lightweight, reconfigurable handpiece that allows the user the option to use the tool as either a gun or pencil style handpiece by simply removing or adding the Handle.

Included:

Desoldering Handpiece (FM2024-02)
Desoldering Control Module (C1492)
Desoldering Handpiece Grip (B2872 for Gun Style Configuration)
Handpiece Holder (FH200-05 – Includes Hakko 599B Tip Cleaner)
Nozzle Remover (B2876)
Cleaning Drill (B2873)
Sleep Mode Cord (B3253)
Filter Pipe (A1511)

Hakko FM2026-KIT N2 Soldering System

FREE UPS GROUND SHIPPING

bnr_n2_250x51

NOTE:

Used together with HAKKO FM-202, FM-203, FM-204, FM-205, FX-950, FX-951 and FX-952

FM-2026-KIT includes FM2026-01 (Iron) and FX791-01 (Controller) ONLY – It does not include the FM202 Solder Station or the FX780!

The Hakko N2 soldering system is the ideal solution for all your LEAD-FREE hand-soldering applications. The bench-top FX-780 Nitrogen Generator creates nitrogen gas from filtered, dry compressed air and the FX-791 Nitrogen Controller and FM-2026 Soldering Iron delivers it efficiently and uniformly to the soldering area.

NOTE: If you do NOT have nitrogen availability at your work station, the compact FX-780 Generator is the best bang for your buck.

Compact FX-791 Nitrogen Controller
Controls the flow of nitrogen to the FM-2026 nitrogen iron with the FM-202 and FP-102 soldering stations
Controls the flow level from 0.25 l/min to 2.5 l/min. (recommended level 0.5 – 1.5 l/min.) and should be adjusted to the tip shape
ESD-safe

FM-2026 N2 Soldering Iron (for the FM-202 and FP-102 solder stations)
Supplies hot nitrogen (N2) gas to the soldering area
The nitrogen gas is preheated as it passes along the ceramic heater in the FM-2026 handpiece
Soldering efficiency can be improved as the hot nitrogen creates a preheating effect while reducing the amount of oxygen in the solder connection area (less oxidation)

Hakko FM2029-01 Hot Air Iron Conversion Kit with Iron and Holder

Hakko FM2029-01 Hot Air Iron Conversion Kit with Iron and Holder

Hakko FM2029-01:

Everything you need to add an additional hot air iron to your Hakko FM station
FM2029-01 Includes:
- FM2029-02 hot air iron
- C1574 holder
- B3253 connecting cord
- B2300 tip removal heat pad

Power Consumption	140W
Temperature Range	100-550°C / 200-1030°F
Tip to Ground Resistance	<2 ohms
Tip to Ground Potential	<2mV
Total Length (w/o cord, nozzle)	167mm
Weight (w/o cord, nozzle)	42g
Cord	1.2m

The Hakko FM2029-01 is a soldering iron upgrade for the FM-206 3-Port Rework System.

Hakko FM2030-02 ESD-Safe Heavy Duty Soldering Iron Kit with Holder

Hakko FM2030-02
ESD-Safe Heavy Duty Soldering Iron Kit with Holder

Hakko FM2030-02:

The Hakko FM-2030 Soldering Iron provides a higher mass tip with double the power of conventional T15 tips. This iron is ideal for soldering difficult-to-solder heavy ground planes and/or high heat sink applications.

Power consumption: 24V AC / 140W
Works with the T22 series soldering tips
Tip to ground resistance: Under 2 ohms
Tip to ground potential: Under 2mV
Heating element: Ceramic heater
Compatible with the Hakko FM-203 soldering station and FM-206 rework system

Hakko FM206-DSA 3-Port Rework Station

Free Ground Shipping!

Hakko FM206-DSA configuration:

FM-206 Rework Station with FM-2024-42 desoldering Iron, FM-2029-01 micro hot air pencil, and FM-2027-06 Soldering Iron and three stands.

Hakko FM206-DTS 3-Port Rework Station

FREE GROUND SHIPPING!
FM-206 Desoldering Rework Station with FM-2022 Tweezer, FM-2024 Desoldering and FM-2027 Soldering Irons

Hakko FM206-DTS Features:

The Hakko FM-206 3-Port Rework Station can power any Hakko FM Series handpiece, thus offering the ability for you to tailor the station to fit your specific rework needs. The station’s sleek, compact design minimizes loss of bench space and its powerful ports allow the use of the Hakko FM-2029 single hot air handpiece, and the Hakko FM-2030 heavy duty soldering iron, making this the ultimate rework station.
• Graphic User Interface for easy setup and operation
• 3 simultaneous powered ports
• Self-contained pump for vacuum and air flow
• Digital airflow indicator
• Configurable display in °C or °F
• High performance hot air handpiece ramps up to max temp in < 20 secs
• Capable of hot air rework of 0201, 01005 and up to 10x10mm QFNs
• Meets or exceeds ANSI J-STD-001
• Manual or Automatic profile for hot air
• Auto shutoff with sleep function
• Passcode protected
• Security lock to protect against theft or unauthorized re-location
• Integrates with the Hakko FR-830 and FR-870 Preheaters
• Low cost composite hot air nozzles
• Desoldering delay timer
• Optional footswitch for pump operation
• Option for external gas supply for hot air
• ESD safe by design

• NOTE: Tips and Nozzles are NOT included with station or any configuration. Must order separately.

The Hakko FM206-DTS configuration contains:

(1) FM-2024 desoldering tool (FM2024-42 Kit) Order N3 nozzles here
(1) FM-2022 Parallel Remover (FM2022-05 Kit)
(1) FM-2027 soldering iron (FM2027-06 Kit) Order T15 tips here
• FM206-55 station is included.

Hakko FR-410 140W High Power Desoldering Station

Hakko FR-410 140W High Power Desoldering Station

Free Shipping on orders over $100!

Replaces Hakko 472D

The HAKKO FR‐410 Desoldering Station is designed to fit that need and bridge the gap in power between the 70W HAKKO FM‐204 Desoldering Station, and the 300W HAKKO FR‐400 Ultra Heavy Duty Desoldering Station.

The HAKKO FR‐410 provides 140W of power and has the widest selection of nozzle configurations that can meet almost every need. The station also includes the same popular features from the HAKKO FR‐400 which include an anti‐clogging feature which helps ensure instantaneous application of peak vacuum pressure to the solder joint, a delay timer to prevent premature release of the vacuum system before solder has cleared the heater and is captured in the solder collection chamber, a large, easy to read display that includes a vacuum level indicator to let you know if there are restrictions building that will need to be cleaned out, 3 user programmable presets, and process control password lockout to prevent any unauthorized changes to the systems operation or setup.

Hakko FR-870B 2-Bank IR Board Preheater

Hakko FR-870B 2-Bank IR Board Preheater

Hakko FR-870B 2‐Bank IR Preheater description:

The Hakko FR-870B is an updated replacement for the popular Hakko FR‐870 IR Preheater that includes an upgrade to use the new high efficiency carbon filament lamps that nearly eliminates the visible spectrum while maintaining a very high output in the infrared spectrum with minimal shadowing, allowing for a very even preheating of the PCB.

The Hakko FR-870B also includes an upgrade to use the new software features found in the FR‐872 4‐ Bank IR Preheater, allowing you to control the ramp rate at 1, 2, or 3 degrees Celsius per second when you are in one of the two thermocouple modes.

The Hakko FR-870B has 2 switchable zones for heating and still offers the same low profile and with a simple integrated PCB holder that is very easy to setup, automatic operation modes allowing for a 3‐ heating zone profile that can be programmed into the system, and a total of 10 profiles that can be stored for each automatic operation mode.

The FR-870B can also be integrated for start/stop operation in conjunction with the popular FR‐803B Hot Air Rework Station, or the FM‐ 206 3‐Port Rework System (integration requires an optional connection cable that is not included).

Hakko FR-872 1440W IR Preheater

Hakko FR-872 1440W IR Preheater

HAKKO FR-872 4-Bank IR Preheater provides a fast and efficient method of preheating large and small PCB assemblies while still on the workbench but in a very controlled fashion. This preheater uses a new high efficiency carbon filament IR heating lamp that nearly eliminates the visible spectrum while maintaining a very high output in the infrared spectrum with minimal shadowing, allowing for a very even preheating of the PCB.

The HAKKO FR-872 has the same operation as the smaller HAKKO FR-870 but has 4 switchable zones of preheating compared to just 2.and both manual and automatic modes of operation using either a thermocouple for closed-loop feedback of the PCB heating, or using power settings of the heaters.

A new feature that has been added for the HAKKO FR-872 is the Ramp Control. This new feature allows you to control the ramp rate of the PCB when using either of the thermocouple modes of temperature control. The feature allows you to select ramp rates of 1, 2, or 3 degrees Celsius per second. Settings of the preheater can be locked out using a password to prevent inadvertent changes that could affect the process.

As with the HAKKO FR-870, the new HAKKO FR-872 allows for automatic operation following a 3-heating zone profile that can be programmed into the system. A total of 10 profiles can be stored for each mode of operation, for a total of 20 possible profiles. The HAKKO FR-872 also integrates for start/stop operation to work in conjunction with the hot air rework profiles programmable into the HAKKO FM-206 or HAKKO FR-803B (integration requires an optional connection cable that is not included).

Hakko FR830 Pre-Heater

Hakko FR-830 Pre-Heater

FREE UPS GROUND SHIPPING

The Hakko FR-830 is a compact and low cost solution to preheating printed circuit boards. The design of the FR-830 delivers consistent heat to the bottom of printed circuit boards and is particularly beneficial when soldering lead-free assemblies.

The integrated self-resetting overheat protection, high pressure fan, and convex outlet reduces heat buildup and prevents blockage of the outlet, and the angled heater tube protects the heating element from damage caused by debris that may accidentally drop inside the heater opening.

Closed loop temperature control allows the output air temperature to be set anywhere between 150° – 300°C (302° – 572°) and an optional Extension Pipe (B3263) extends the airflow an additional 27mm (1.1 inch).

The FR-830 also has a port that allows it to be activated by an optional hand switch (B2763) or foot switch (B1649).

Compact design; Measures only 5.5(w) x 3.0(h) x 7.3(d) in. [140(w) x 75(h) x 185(d) mm]
• Fast heating
• Excellent thermal stability
• ESD-safe by design

Hakko FS-100 Solder Tip Tinner Cleaner

Hakko Lead Free Solder Tip Tinner & Cleaner .35 oz

The Hakko FS-100 Solder Tip Tinner Cleaner is a chemical paste best suited for the removal of oxidation on soldering iron tips.

For retinning soldering tips
For oxidation removal on soldering tips
As Diamnonium phosphate is not included, P.W.B. is not corroded due to flux residue. (Conforming to the JIS-Z-3197 6.6.1 test method)
Use FS-100 in combination with HAKKO FT-700 for enhanced effectiveness.

Use example of FS-100

→ →

HAKKO FT-700 Tip Polisher

HAKKO FT-700 Tip Polisher

The Hakko FT-700 is great for Lead-Free solder!

When hand soldering with Lead-Free alloys, higher tip temperatures and highly-active fluxes causes oxidation and corrosion, which greatly decreases the life of your soldering iron tip. The Hakko FT-700 tip polisher helps increase the life of your tip by keeping it clean and free from oxidation easily and quickly.

Fast and easy way to keep your soldering iron tips clean and free from oxidation
Two spinning polishing brushes (brushes will not damage tip plating)
Lead-free chemical paste for immediate tip tinning
Removes oxidation caused by higher temperatures and high activity fluxes
Extends tip life by removing oxidation

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko FT-700 Tip Polisher

FREE UPS GROUND SHIPPING

The Hakko FT-700 Tip Polisher is the ideal maintenance kit to renew oxidized soldering iron tips, especially when soldering with Lead-Free alloys.

FAST and EASY way to keep your soldering iron tips clean and free from oxidation
Two spinning polishing brushes (brushes will not damage tip plating)
Lead-free chemical paste for immediate tip tinning
ESD safe by desigm

Total Power Consumption: 120V – 430W
Pump Type: Diaphragm pump
Pump Capacity: 5 to 20 l/min. (max)
Control Temperature: 100 to 420

Hakko FT-710 Tip Cleaner

Hakko FT-710 Tip Cleaner

The HAKKO FT-710 Tip Cleaner is designed to quickly and effectively clean your soldering iron tip. The counter-rotating brushes remove tip oxides, debris, and excess solder without damaging the tip plating, and the soldering iron specific receptacle collar provides accurate positioning of the tip for optimal cleaning while mitigating FOD potential from the spatter of the solder that is cleaned from the tip

The tip cleaner is activated only when the tip is pressed into the holder. The tip cleaner can also be mounted to existing FH-200 Series Iron Holders in place of the sponge/tip cleaner tray.

• FAST and EASY way to keep your soldering iron tips clean and free from oxidation

• Two powerful spinning brushes (brushes will not damage the tip plating)

• Internal collection tray for easy removal and disposal of solder waste

• AC adapter included

When hand soldering with Lead-Free alloys, higher tip temperatures and highly-active fluxes causes oxidation and corrosion, which greatly decreases the life of your soldering iron tip. The Hakko FT-710 will help increase the life of your tip by keeping it clean and free from oxidation easily and quickly.

Hakko FX-601 Adjustable Temperature Soldering Iron

Hakko FX-601 Adjustable Temperature Soldering Iron

The Hakko FX-601 Soldering Iron is the next generation of variable temperature-controlled soldering irons. It is ideal for soldering applications that require mobility or a long reach, such as soldering solar panels, etc. The extremely lightweight, ergonomic handpiece allows you to solder for long periods of time without hand fatigue.

The soldering iron also features a convenient temperature adjustment dial in the handpiece that allows the user to select their optimal soldering temperature, and the advanced electronic controls and efficient ceramic heater provide accuracy and stability that rival older Hakko stick irons.

The Hakko FX-601 also features a longer power cord for better reach with the iron and includes a temperature adjustment tool that can be used to ‘adjust and lock’ the selected temperature of the iron if necessary by removing the adjustment dial.

Power Consumption; 67W 120VAC
Tip-to-Ground: < 2 Ω
Leak Voltage: < 2 mV
Temp Range: 240-540°C (464-1004°F)
Temp Accuracy: ±10°C (±18°F)
Temp Stability: ±1.0°C (±1.8°F)
Heater Type: Ceramic
Length: (w/o cord) 235 mm (9.25 in.) w/T19-D5
Tip Weight: (w/o cord) 68 g (0.1 lb)
Reach: 1.8 m (6.0 ft)
Tips: T19 Series
Standard Tip: T19-D5
Shipping Size 273 x 114 x 38 mm (10.75 x 4.5 x 1.5 in)
Shipping Weight 254 g (0.56 lb)

Solder tips for FX-601