JT&T 4272F 3/8″ Asphalt-Coated Fabric Loom, 10 ft

JT&T Asphalt-Coated Fabric loom is a flame-retardant, non-metallic flexible conduit woven from the highest grade yarns & fibers. Standard products are a blend of cotton/poly fiber, PET monofilament & an asphaltic resin. Meets MIL-Spec, SAE-Spec, Ford, Chrysler & General Motor Specifications. Military Specs: HH-T-791 A,B,C. SAE Spec: SAE-J562A. Ford Specs: ESB-M3L38-A, ESF-M3L45-A, ESB-M99H96. Chrysler Specs: MS-542, MSJZ9-31. GM Specs: GM-675, 676, 677, 678-M, Packard Electric Speck: PM451. Fabric Loom is available in additional sizes & in additional colors by special order. Woven loom is typically shock absorbent, completely flexible, dimensionally stable & sound absorbent. Woven loom is often used in wire harnesses, fuel and vacuum lines, battery cables, oil indicators, control rods, EGR tubes and mold ducts. Specifically it has been used to protect truck battery cables during engine installation, prevent damage to starter cables during engine installation, prevent damage to wiring where exposed to sheet metal, protect copper air brake lines from stone damage & protect jumper wires between tractors & trailers. It is coated with a special flame-retardant, black bituminous coating & is ideal for harsh environments. Available in additional sizes, formulations & in additional colors by special order. Temperature rating from -40°C (-40°F) to 135°C (275°F)

Meets requirements of SAE-J562A & HH-T-791 A,B,C.
Meets Ford, Chrysler, GM & Packard Electric Specifications (see above).
Continuous Operating Temperature: -40C (-40F) to 135C (275F).
Maximum Temperature: 176C (350F).
Flame-Retardant Coating: Yes.
Material: Asphalt-Coated Fabric Loom.
Longer lengths may not be a continuous piece, and may be spliced

JT&T 4273F 1/2″ Asphalt-Coated Fabric Loom, 10 ft

JT&T 4404C 1/2″ Grommets

1/2″ Grommets feature a 3/8″ ID, 1/2″ hole diameter, and 1/16″ groove.

Grommets are inexpensive, flexible, oil resistant and have high dielectric strength with outstanding aging qualities.

See Specifications tab for measurements.

JT&T 4408H 1″ Grommets

1″ Grommets feature a 11/16″ ID, 1″ hole diameter, and 1/16″ groove.

Grommets are inexpensive, flexible, oil resistant and have high dielectric strength with outstanding aging qualities.

See Specifications tab for measurements.

JT&T 4450H Assorted Grommets with 1/4″, 5/16″, 3/8″ Mounting Holes, Black

1/4″ Grommets x 5, 5/16″ Grommets x 4, 3/8″ Grommets x 4

JT&T rubber grommets are inexpensive, flexible, oil resistant and have high dielectric strength with outstanding aging qualities.

See Specifications tab for measurements.

JT&T 4495F Insulated Cable Clamps, 7/8, 1, 1-1/4, & 1-1/2″, 2 Each

JT&T’s Rubber Insulated Clamps are made with cold rolled steel and have a 1/4″ mounting hole. Attributes include soft-touch, durability, resistance to heat and various fluids. Rubber is an excellent insulator for electrical installation and provides a consistant thickness throughout.

JT&T 4653H-0 Nylon Clamp Assortment – Black

Open Inner Diameters: 0.75”, 1”, & 1.125”. Black. Mounting Hole 13/64”

JT&T 4790F 650pc Wire Tie Kit

4701 4” 18Lb. Natural Wire Ties 200
4702 4” 18Lb. UV Black Wire Ties 100
4701-7 4” 18Lb. Yellow Wire Ties 20
4701-6 4” 18Lb. Blue Wire Ties 20
4701N5 4” 18Lb. Neon Green Wire Ties 20
4701N8 4” 18Lb. Neon Pink Wire Ties 20
4701N3 4” 18Lb. Neon Orange Wire Ties 20
4705 7.5” 50Lb. Natural Wire Ties 100
4706 7.5” 50Lb. UV Black Wire Ties 10
4705-2 7.5” 50Lb. Red Wire Ties 10
4705-7 7.5” 50Lb. Yellow Wire Ties 10
4705-6 7.5” 50Lb. Blue Wire Ties 10
4705-4 7.5” 50Lb. Purple Wire Ties 10
4707 11.5” 50Lb. Natural Wire Ties 100

JT&T 4794F 1,200pc Wire Tie Kit

4701 4” 18Lb. Natural Wire Ties 100
4702 4” 18Lb. UV Black Wire Ties 200
4701-6 4” 18Lb. Blue Wire Ties 100
4701-4 4” 18Lb. Purple Wire Ties 100
4701N5 4” 18Lb. Neon Green Wire Ties 100
4701N7 4” 18Lb. Neon Yellow Wire Ties 100
4701N3 4” 18Lb. Neon Orange Wire Ties 100
4703 5.5” 40Lb. Natural Wire Ties 100
4704 5.5” 40Lb. UV Black Wire Ties 200
4706 7.5” 50Lb. UV Black Wire Ties 100
304705-1 7.5” 250Lb. Stainless Steel Wire Ties 2

JT&T Black Cable Clamp

Black Cable Clamp – 100/pack

JT&T Insulated Cable Clamps

25/pack

JT&T Split Wire Loom Flex-Guard Convoluted Tubing

JT&T’s Polyethylene Flex-Guard Convoluted Tubing (Split Loom) is designed to provide a flexible, crush-resistant protection for wiring assemblies. The tubing is a corrugated tube used to provide protection to a wire harness or any other product that may be subject to abnormal conditions, such as continuous abrasion & vibration wear, puncturing, water, snow, ice, salt & UV rays. Flexible convoluted tubing/conduit is manufactured from a blend of low density polyethylene & linear low density polyethylene resins. The convoluted surface enhances the appearance of your product by providing a uniform tailored finish. The split seam feature allows wires to be inserted easily, eliminating the costly time needed to apply tape, braid or loom. Since the seam is not permanently sealed, the costs of repair or service are also reduced. Temperature rating from -40°C (-40°F) to 93°C (200°F).

Meets requirements of ASTM D792 density test.
ISO/TS 16949 & ISO 9001 Compliant.
RoHS Compliant.
Continuous Operating Temperature: -40dC (-40dF) to 93dC (200dF).
Flexibility: Excellent.
Flame-Retardant: No.
Material: Polyethylene.
Use 5024F tool to easily pull wires & cables through split loom

JT&T Yellow Split Wire Loom Flex-Guard Convoluted Tubing

Klein Tools 450-400 Self-Adhesive Cable Mounting Clips, 1 Slot (10-Pack)

Route and organize messy cables with self-adhesive cable mounting clips. Each clip features a single slot to hold cables of different sizes. The 3M adhesive backing mounts to a wide variety of surfaces. Screws are included for permanent mounting if needed. Sold in a pack of 10.

Self-Adhesive Mounting Clips organize and route cable or wire
10-Pack
Single slot accommodates a variety of cables including data cables, charge cords, power cords and more
Includes optional screws for permanent mounting; mounts to a variety of surfaces
Made in USA
Quality 3M adhesive backing holds up to 194-Degree Fahrenheit (90-Degree Celsius)
3M is a registered trademark of 3M Company

Klein Tools 450-410 Self-Adhesive Cable Mounting Clips, 3-Slot (10-Pack)

Route and organize cables with these cable mounting clips. Each clip features three slots to hold cables of different sizes. The 3M adhesive backing lets you mount to a wide variety of surfaces. Screws are included for permanent mounting. Sold in a pack of 10.

Self-Adhesive Mounting Clips organize and route cables or wires
10-Pack
Three slots hold a range of cable sizes
Includes optional screws for permanent mounting; mounts to a variety of surfaces
Made in USA
Quality 3M adhesive backing holds up to 194-Degree Fahrenheit (90-Degree Celsius)
3M is a registered trademark of 3M Company

PLATINUM 15030C CABLE STRIPPER

Platinum Tools 15030C Two-Level Coaxial Cable Stripper

Simple to operate and a pleasure to use, the 15030C Two-Level Coaxial Cable Stripper from Platinum Tools has an adjustable stripping depth, but comes pre-set with the industry standard 1/4″ stripping size. Your E Series cable stripper includes a hex wrench for adjusting blade depth and uses drop-in replacement blades. For strength and durability, this tool is made of molded, high-impact plastic.

-Works with RG58/59/62/6/6 quad coax cables

-Adjustable stripping depth for various insulation types and thicknesses

-Pre-set for 6mm (referred to as the 1/4″ strip) but adjusts to additional dimensions

-Uses drop-in replacement blades, no cassettes required

-Hex wrench snaps into housing for convenient storage

-Molded from high-impact plastic for long life

-Adjustable to additional settings 0.157, 0.315, and 0.472″ (4, 8, and 12mm)

Avery Dennison 10027-2 Tie Anchor Base #8 Screw

Avery Dennison 10027 Tie Anchor Base #8 Screw

100/pack

Tie Anchor Base, #8 Screw

Length: .750″

Width: .380″

Thickness: .210″

Avery Dennison 10028-2 Cable Tie Anchor Base #10 Screw

Avery Dennison offers this anchor base as a cable tie accessory. Cable tie mounts stabilize and secure wiring bundles in a variety of cable & wire management applications. These base mounts fit a range of cable sizes all securely tied up with a cable tie. Each base is designed for screw mounting only & can be used with miniature, intermediate, and standard size cable ties.

Attribute	Specifications
Environmental Requirements	General Purpose
Width	0.38″ (9.7mm)
Length	0.75″(19mm)
Quantity Per Bag	100

Part #	Screw Size	Panduit Cross Reference	Thomas and Betts Cross Reference
10028-0	#10 Screw	TA1S10-C