Fluke 373 True RMS AC/DC Clamp Meter 600A

FREE UPS GROUND SHIPPING

Be ready for anything.

The new Fluke 373 True RMS AC/DC Clamp Meter 600A offers improved performance, perfect for many ac only current measurement situations. With true-rms ac voltage and current measurements, the Fluke 373 reads up to 600 A ac and 600 V ac or dc.

Featuring True RMS AC voltage and current measurements, and resistance measurement up to 6000 Ω with continuity detection, the Fluke 373 is everything you need, plus a little more.

600 A ac current measurement with fixed jaw
600 V ac and dc voltage measurement
True-rms ac voltage and current for accurate measurements on non-linear signals
Resistance measurement to 6000? with continuity detection
1000 ?F capacitance measurement
State of the art signal processing allows for use in noisy electrical environments while providing stable readings
Large, easy to read, backlight display automatically sets the correct measurement range so you do not need to change switch positions while taking a measurement
CAT IV 300 V, CAT III 600 V safety rating
Three-year warranty
Soft carrying case

373 Users Manual

Fluke 365 Detachable Jaw True-rms AC/DC Clamp Meter

FREE UPS GROUND SHIPPING

The Fluke 365 is a rugged meter perfect for jobs where access to wires is difficult. The 365’s thin, small jaw is detachable with a flexible lead, which makes gaining access to wires and viewing the display easier than ever.
Safety Conformance
IEC/EN 61010-1:2001, 600V CAT III

200 A ac and dc current measurement with detachable jaw
600 V ac and dc voltage measurement
Detachable jaw makes accessing wires and viewing the display easier
Built in flashlight/torch allows for easy illumination and identification of wires
CAT III 600 V
Compact design fits in your hand and can be used while wearing protective equipment
State of the art signal processing allows for use in noisy electrical environments while providing stable readings
Large, easy to read, backlight display automatically sets the correct measurement range so you do not need to change switch positions while taking a measurement
Three-year warranty
Soft carrying case

Be ready for anything.

Safety Conformance
IEC/EN 61010-1:2001, 600V CAT III

en61010-1-600cat3_xx

FLUKE TLK-225 Suregrip Master Accessory Set

FREE UPS GROUND SHIPPING

TLK-225 SUREGRIP MASTER ACCESSORY SET

Includes all the SureGrip™ leads and probes in a handy six-pocket, roll-up pouch, along with TL224 test leads.

Test leads are an integral part of the complete measurement system. Worn out test leads can cause inaccurate readings and pose serious shock or electrocution hazard. The Fluke TLK-225 SureGrip™ Master Accessory Set with 13 items is the perfect replacement kit that provides flexibility and comfort with all SureGrip™ leads and probes in a convenient six pocket, roll up pouch.

Leads and Probes in a Handy Roll-up 6 Pocket Storage Pouch
AC220 SureGrip Alligator Clip Set
AC280 SureGrip Hook Clip Set
AC283 SureGrip Pincer Clip Set
AC285 SureGrip Large Jaw Alligator Clip Set
TP220 SureGrip Test Probe Set

Fluke 233 Remote Display Multimeter

FREE UPS GROUND SHIPPING

Imagine the Possibilities

With its removable display, the Fluke 233 Digital Multimeter with True RMS gives you the flexibility to take measurements in hard to reach places or in areas with restricted access. You can be in two places at once and reduce the risk of arc flash by separating yourself from hazardous measurement situations.

The new Fluke-233 has a removable magnetic display that works up to 33 feet away

Make Measurements Without Holding the Meter
True-RMS AC Voltage and Current
Measure up to 1000V AC and DC
Measure up to 10A (20A for 30 seconds)
10,000uF Capacitance Range
Frequency to 50khz
Built in Thermometer
Resistance, Continuity and Diode Test
233 Users Manual

Fluke LVD2 Volt Light Tester

Fluke LVD2 Volt Light

Non-contact AC voltage detector and LED flashlight combined into one easy to use pen-style design. The LVD2 is a CAT IV 600 V rated non-contact detector that is suitable for commercial and industrial applications. The LVD2 includes dual sensitivity turning blue 1 to 5 (2.54 cm to 12.7 cm) from the source and red when at the source.

Ultra-Bright White LED with 100,000 hour life
Detects from 90 to 600 V AC
Rated to CAT IV 600 V
Dual Levels of Detection
Blue indicates proximity to AC Voltage source
Red indicates you’re at the source
Operating temperature 0 deg C to 50 deg C

Fluke i800 AC Current Clamp Probe

FREE UPS GROUND SHIPPING

The Fluke i800 is a clamp-on AC current probe designed to extend the current measuring capability of a digital multimeter to 800 amperes AC. The clamp is compatible with a DMM that accepts 4mm shrouded banana plugs and has an AC milliamp range.

Measures AC current from 100mA to 800 A rms
30 Hz to 10 kHz frequency range
CAT III 600 V rating
Accepts up to 54 mm (2.1 in) diameter conductor size
1000:1 conversion factor for easy calculation
Rugged positive action design

Manufacturer does not allow discounted prices to be advertised. Call us for DISCOUNT PRICE or Add to cart and use promo code: PROMO9 at checkout to see DISCOUNT PRICE.

Fluke i400 AC Current Clamp

FREE SHIPPING

The i400 is a single range 400 A ac current clamp with current output via safety shrouded banana plugs. The clamp is compatible with most Fluke multimeters or any other current measurement device that accepts 4mm-shrouded banana plugs and has an AC milliamp range. The division ratio is 1000:1.

Companion to your DMM to measure up to 400A AC
1mA/Amp output guarantees easy reading on you meter
Only current clamp available with a CAT IV 600 V / CAT III 1000 V safety rating
Specially designed to offer maximum utility in a very compact shape
Take accurate current readings without breaking the circuit
Soft non-slippery overmold handle prevents from accidental touching live wiring

Fluke i3000s AC Current Clamp

FREE UPS GROUND SHIPPING

Very High AC Current Clamp

Fluke Current clamps are the ideal tools to extend the current ranges of Fluke tools.
The i3000s is a clamp-on AC Current Clamp for use with oscilloscopes and multimeters with banana input using the supplied Dual Banana to BNC Adapter. The clamp is optimized for measurement on power distribution systems.

The Fluke i3000s is a clamp-on AC Current Clamp for use with oscilloscopes and multimeters with banana input using the supplied Dual Banana to BNC Adapter. The clamp is optimized for measurement on power distribution systems.

Nominal current range: 30A, 300A, 3000A
Continuous current range: 1A – 30A, 1A – 300A, 1A – 3000A
Maximum Non-Destructive Current: 4000A
Useable frequency: 10 Hz – 100 kHz
CAT III, 600 V

i3000s Instruction Sheet

Fluke i200s AC Current Clamp

FREE UPS GROUND SHIPPING

The Fluke i200s is a dual range 20A and 200A ac current clamp with voltage output via a safety insulated BNC connector. A dual banana to BNC adapter is supplied to allow the i200s to be connected to multimeters with banana inputs.

Companion to your scopemeter, power quality meter or digital multimeter to measure up to 200A AC
Included adapter for DMM’s
Two ranges: 20 A & 200A, 10 or 100 mV/ Amp output
Take accurate current readings without breaking the circuit
CAT III 600V safety rating

Fluke T+ Electrical Tester

Fluke T Electrical Tester

The Fluke T Electrical Tester has all the advantages of traditional solenoid testers, with none of the typical solenoid tester drawbacks. The T uses all 3 voltage detection methods – light, sound and vibration, to work more efficiently in noisy environments, dimly lit areas, or tight spaces. Built-in flashlight, GFCI trip capability, and the legendary ruggedness you expect from Fluke, make the T an excellent choice for most industrial, commercial, and residential applications.

- CAT IV 600 V, CAT III 1000 V rated
- AC/DC Voltage: 12 V – 600 V on LED bar
- Continuity beeper
- Detects live voltage even when the batteries are dead
- GFCI Trip
- Bright LED flashlight for work in poorly lit areas
- On/Off switchable beeper, selectable according to your environment
- Replaceable test probes for added flexibility and convenience
- Hazardous voltage warning light for added user protection
- Test lead strap included for better test lead management
- Auto off mode to conserve battery life
- 2-year warranty

Fluke 922 Airflow Meter/Micromanometer

FREE UPS GROUND SHIPPING

The Fluke 922 makes airflow measurements easy by combining three tools: differential pressure, airflow, and velocity into a single, rugged meter. Measure pressure drops across key HVAC equipment to drive peak performance and extend equipment life. Monitor indoor vs. outdoor pressure relationships and manage the building envelope. Perform duct traversals for accurate airflow readings.

Powerful meter provides differential and static pressure, air velocity and flow readings
Convenient colored hoses help proper interpretation of pressure readings
Easy to use without sacrificing performance
Bright, backlit display for clear viewing in all environments
User-defined duct shape and size for maximum airflow accuracy
Resolution down to 0.001 in H2O
99 point data storage capacity
Min/Max/Average/Hold functions for easy data analysis
Auto power off saves battery life

Fluke 789 ProcessMeter

FREE UPS GROUND SHIPPING

Now compatible with Fluke Connect™ App

The Fluke 789 ProcessMeter is the ultimate troubleshooting tool for electricians and instrumentation professionals, combining the functionality of a loop calibrator with the power of a digital multimeter. By equipping the 789 with a temperature measurement module and the wireless data logging capabilities of Fluke Connect™ with ShareLive™ video call (sold separately), process technicians can now do a lot more while carrying a lot less. And with its built-in, selectable 250 ohm HART® resistor, it eliminates the need to carry a separate resistor with you.

4 V Loop power supply
Very large dual display
Enhanced backlight with 2 brightness settings
1200 Ohm drive capability on mA source
HART mode setting with loop power and a built-in 250 ohm resistor
0% and 100 % buttons to toggle between 4 and 20 mA sourcing for a quick span check
Infrared-port to process data in FlukeView Forms (V2.1) software
Precision 1000 V, 440 mA True-RMS digital Multimeter
0.1% dc voltage accuracy
0.05% dc current accuracy
Frequency measurement to 20 kHz
Min/Max/Average/Hold/Relative modes
Diode Test and Continuity Beeper
Simultaneous mA and % of scale readout
20 mA DC current source / loop calibrator / simulator
Manual Step (100%, 25%, Coarse, Fine) plus Auto Step and Auto Ramp
Externally accessible battery for easy battery changes

Fluke 771 Milliamp Process Clamp Meter

FREE UPS GROUND SHIPPING

Measure 4-20 mA signals without breaking the loop with this new, compact clamp meter for PLC and control systems analog I/O. The detachable clamp with extension cable allows you to take measurements in tight locations, and the built-in spot light illuminates hard to see wires in dark enclosures.

Measure mA signal for PLC and control system analog I/O
Count on best in class accuracy of 0.2%
Measure mA signals with 0.01mA resolution
Three year warranty for electronics, one year for clamp cable assembly

Fluke 289 True-RMS Industrial Logging Multimeter

FREE UPS GROUND SHIPPING

Now compatible with Fluke Connect™ Mobile App

The 289 is the next generation high performance industrial logging multimeter designed to solve complex problems in electronics, plant automation, power distribution, and electro-mechanical equipment. With the ability to log data and review it graphically on-screen, you can solve problems faster and help minimize downtime. Let the new 289 be your watchdog for systems or processes while you are off doing other jobs. Now communicate wirelessly with your iOS and Android smart devices with the Fluke Connect mobile app and ir3000 FC wireless connector (sold separately).

- NEW – Now compatible with Fluke Connect mobile app and all Fluke FC enabled test tools with optional ir3000 FC infrared connector (sold separately).
- NEW – Let your team see what you see in an instant with ShareLive™ video call (requires Fluke Connect mobile app and ir3000 FC wireless connector).
- TrendCapture graphically displays logged data session to quickly determine whether anomalies may have occurred.
- Zoom on trend provides unprecedented ability to view and analyze TrendCapture data; zoom in up to 14 times.
- Selectable AC filter (smoothing mode) helps display a steadier reading when the input signal is changing rapidly or noisy.
- Adjustable recording and auto hold thresholds, specify a percentage change in the readings that begins a new event.
- Large 50,000 count, 1/4 VGA dot matrix display with white backlight.
- Logging function with expanded memory for unattended monitoring of signals over time. Using on-board TrendCapture users can graphically review logged readings without needing a PC. Store up to 15,000 recorded events.
- Save multiple logging sessions before PC download is necessary.
- Two terminal 50 ohm range with 1 milliohm resolution, 10 mA source current. Useful for measuring and comparing differences in motor winding resistance or contact resistance.
- Low Pass filter for accurate voltage and frequency measurements at the same time on adjustable speed motor drives and other electrically noisy equipment.
- LoZ Volts. Low impedance voltage function for eliminating ghost voltages. Also recommended when testing for absence or presence of live power.
- On board help screens for measurement functions. Unsure about a function – go to that function and press the “i” button.
- Real time clock for automatic time stamping of saved readings.
- Relative mode to remove test lead resistance from low ohms or capacitance measurements.
- True-RMS AC voltage and current for accurate measurements on non-linear signals.
- Measure up to 10 A (20 A for 30 seconds).
- 100 mF capacitance range.
- Peak capture to record transients as fast as 250 μs.
- Premium test leads and alligator clips included.
- Amp jack plugs included.
- Optional magnetic hanger for easy setup and viewing while freeing your hands for other tasks.
- Optional FlukeView forms enable you to document, store and analyze individual readings or a series of measurements, then convert them into professional-looking documents.
- Limited lifetime warranty.

Fluke 287 True-RMS Electronics Logging Multimeter

FREE UPS GROUND SHIPPING

For electronics professionals who demand the best in performance, accuracy and capabilities, we introduce the Fluke 287 Electronic True-RMS logging multimeter with TrendCapture. Use it to quickly characterize and document design performance. TrendCapture allows the engineer to graphically view logged readings after the recording session right on the DMM display. Scroll buttons and soft keys offer easy navigation and custom displays.

Large 50,000 count, 1/4 VGA display with white backlight for fast, accurate viewing of measurements
Logging Function with TrendCapture plots measurements as single line to help detect anomalies over time, storing up to 10,000 readings
0.025 % basic dc accuracy
100 kHz AC bandwidth
Battery saving sleep mode allows data logging for over 200 hours uninterrupted
Event and trend recording Helpful for troubleshooting intermittent problems or profiling loads
Soft keys and scroll buttons for easy navigation control, access to secondary functions, and custom displays
Saved measurements allows the user to name and recall measurements made in the field
Dual rated CAT IV 600 V/CAT III 1000 V
Limited Lifetime Warranty

Fluke 125B 40MHz Scopemeter

Fluke 125B 40MHz Scopemeter

FREE UPS GROUND SHIPPING

The Fluke 125B 40MHz Scopemeter: All the power of the 120-Series plus Industrial Bus Health Test capabilities and advanced power measurements on top.

The compact Fluke 125B 40MHz Scopemeter is the rugged solution for industrial troubleshooting and installation applications. Based on the Fluke 120 series, the 125 has all the capabilities of the 124 ScopeMeter extended with the capability to measure and analyze the signal quality on the common industrial buses.

The Fluke 125 ScopeMeter combines a 40MHz dual input digital storage oscillo-scope, two true-RMS digital multimeters and a dual input TrendPlot recorder all in a compact, battery powered instrument. Leave all other test tools behind, the Fluke 125 ScopeMeter is the only tool you’ll need.

Dual-input 40 MHz digital oscilloscope
Two 5,000 counts true-RMS digital multimeters
A dual-input TrendPlot recorder
Shielded test leads for oscilloscope, resistance and continuity measurements
10:1 Voltage Probe included for high frequency measurements
600 V CAT III safety certified
Up to 7 hours battery operation
Optically-isolated interface for PC connection
3 year warranty on main instrument, 1 year on accessories

SOFTWARE NOT INCLUDED

125 Getting Started

Fluke 117 True-RMS Multimeter

FREE UPS GROUND SHIPPING

The compact Fluke 117 true RMS digital multimeter is optimized to help you keep commercial buildings, hospitals and schools running right.

The advanced features of the Fluke 117 help you get the job done, quickly and safely. Integrated non-contact voltage detection helps you identify energized circuits. The AutoV/LoZ function prevents false readings caused by ghost voltage. The Fluke 117 delivers true-rms ac voltage and current readings with 6000-count resolution. It provides Min/Max/Average readings and measures frequency and capacitance. The battery door is easy to access, so you and your Fluke 117 can stay on the job.

Fluke 117 multimeters are independently tested for safe use in CAT III 600V environments.

- VoltAlert™ technology for non-contact voltage detection
- AutoVolt automatic ac/dc voltage selection
- Low input impedance: helps prevent false readings due to ghost voltage
- Large white LED backlight to work in poorly lit areas
- True-rms for accurate measurements on non-linear loads
- Measures 10 A (20 A overload for 30-seconds)
- Resistance, continuity, frequency and capacitance
- Min/Max/Average with elapsed time to record signal fluctuations
- Compact ergonomic design for one-handed operation
- Compatible with optional magnetic hanger (ToolPak™) for hands free operation
- CAT III 600 V safety rated
AutoVolt/LoZ
VoltAlert

Case: C90

Fluke 116 HVAC Multimeter

Fluke 116 HVAC Multimeter

FREE UPS GROUND SHIPPING

The Fluke 116 digital multimeter delivers the capabilities professionals demand to troubleshoot and repair HVAC (heating, ventilation and air conditioning) systems. It has everything you need in an HVAC meter, including temperature and microamp measurements to help you quickly troubleshoot problems with HVAC equipment and flame sensors.

The Fluke 116 comes with the Fluke 80BK-A integrated DMM temperature probe. The microamp function allows flame sensor measurement down to 0.1 microamps. The AutoV/LoZ function prevents false readings caused by ghost voltage. The Fluke 116 also has a large white LED backlight for work in poorly lit areas. It measures resistance, continuity, frequency, and capacitance and provides Min/Max/Average readings with elapsed time to record signal fluctuations.

Fluke 116 multimeters are independently tested for safe use in CAT III 600V environments.

Built-in thermometer for HVAC applications
Microamps to test flame sensors
Low input impedance: helps prevent false readings due to ghost voltage
Large white LED backlight to work in poorly lit areas
Resistance, continuity, frequency and capacitance
Min/Max/Average with elapsed time to record signal fluctuations
Compact ergonomic design for one-handed operation
Compatible with optional magnetic hanger (ToolPak™)
CAT III 600 V safety rated