Klein Tools ET310 Digital Circuit Breaker Finder with GFCI Outlet Tester

The Klein Tools ET310 Circuit Breaker Finder with Integrated GFCI Outlet Tester is a digital circuit breaker finder used to locate the correct circuit breaker in a panel to which an electrical outlet or fixture is connected. The Transmitter is connected to the electrical outlet or fixture in the circuit while the receiver is used to scan the breakers in the circuit panel. The Transmitter also features a GFCI outlet tester.

This circuit breaker finder can quickly and accurately locate the correct circuit breaker in a panel corresponding to the circuit to which an electrical outlet or fixture is connected
GFCI tester consists of two parts: a Transmitter connected to the electrical outlet or fixture, and a Receiver used to scan the panel to locate the correct breaker
Receiver delivers clear visual and audible indications when the correct breaker has been located
Operates on 90-120V AC circuits
Transmitter incorporates a GFCI outlet tester to inspect the wiring condition at the electrical outlet and test GFCI devices
Transmitter docks in the Receiver for convenient storage as a single item when tester is not is use
Transmitter incorporates a three-pin plug for connecting to North-American-style grounded electrical outlets
The transmitter may be connected to other electrical fixtures using optional accessories which are sold separately (Cat. No. 69411)
Receiver powers off automatically after approximately three minutes of non-use to conserve battery life
Transmitter is powered by the circuit when connected to the electrical outlet or fixture

Hakko T31-02WD08 Chisel Tip

Hakko T31-02WD08, CHISEL, 0.8 x 6mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

Flat-blade screwdriver Shape.

Capable of soldering by applying the tip in 2 ways: line and face.

Width (size of tip) suitable for the workpiece can be selected.

Can be used for any soldering work.

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Kiesub Electronics is a leading distributor of Hakko soldering equipment. Located in Las Vegas, we stock a wide variety of Hakko soldering stations, desoldering and rework stations, solder tips, desolder nozzles, analog and digital soldering stations, soldering irons and guns, solder and solder paste, and many other soldering accessories.

Hakko T31-02SBL Conical Tip

Hakko T31-02SBL, CONICAL, R0.2×13.7mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

Cone or column Shape cut at a slant.

Allows users to select the cut surface size depending on the workpiece.

Used for drag soldering and pre-tinning of lead wires.

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-02KU Knife Tip

Hakko T31-02KU KNIFE, 4.8mm/45° x 15mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

Shaped like a knife

Capable of soldering by applying the tip in 3 ways: line, face and point

used for soldering at narrow pitches, correction of bridging and drag soldering

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-02JS02 Bent Tip

Hakko T31-02JS02 Bent Tip

Hakko T31-02JS02, BENT, R0.2mm/30° x 1.8mm x6.6mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

Bent tip end

Capable of soldering by applying the tip in 2 ways: face and point

Ideal for drag soldering and correction of bridging

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-02JL02 Bent Tip

Hakko T31-02JL02 Bent Tip

Hakko T31-02JL02, BENT, R0.2mm/30° x 7.2mm x 8mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

Bent tip end

Capable of soldering by applying the tip in 2 ways: face and point

Ideal for drag soldering and correction of bridging

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-02J02 Bent Tip

Hakko T31-02J02, BENT, R0.2mm/30° x 4mm x 11mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

Bent tip end

Capable of soldering by applying the tip in 2 ways: face and point

Ideal for drag soldering and correction of bridging

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-02IL Conical Tip

Hakko T31-02IL Conical Tip

Hakko T31-02IL, CONICAL, R0.2×14.7mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

Thin conical end

Ultrafine tip which is best suited for soldering at narrow pitches, etc

Ideal for soldering micro components such as 0603, etc. and for repairing high-density-mounting P.W.Bs. such as in cellular phones, etc

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-02I Conical Tip

Hakko T31-02I, CONICAL, R0.2 x 8.4mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

Thin conical end

Ultrafine tip which is best suited for soldering at narrow pitches, etc

Ideal for soldering micro components such as 0603, etc. and for repairing high-density-mounting P.W.Bs. such as in cellular phones, etc

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-02D52 Chisel Tip

Hakko T31-02D52 Chisel Tip

Hakko T31-02D52, CHISEL, 5.2 x 7.8mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

Flat-blade screwdriver Shape

Capable of soldering by applying the tip in 2 ways: line and face

Width (size of tip) suitable for the workpiece can be selected

Can be used for any soldering work.

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-02D16 Chisel Tip

Hakko T31-02D16 Chisel Tip

Hakko T31-02D16 ,CHISEL, 1.6 x 10mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Temperature: 750°F (400°C)

This type has a shape like a flat-blade screwdriver and is capable of soldering by applying the tip in 2 ways: line and face.

The width (size of tip) suitable for the workpiece can be selected, and it can be used for any soldering work.

How to use the Shape D and examples

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-02D08 Chisel Tip

Hakko T31-02D08 Chisel Tip

Hakko T31-02D08, CHISEL, 0.8x9mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

This type has a shape like a flat-blade screwdriver and is capable of soldering by applying the tip in 2 ways: line and face.

The width (size of tip) suitable for the workpiece can be selected, and it can be used for any soldering work.

How to use the Shape D and examples

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-02BL Conical Tip

Hakko T31-02BL ,CONICAL, R0.2 x 12mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

This shape is All-round type which can be used from any direction and it is available for any works. Therefore it is not only accessible for the soldering beginners but also suitable for the experienced.

Shape B has the special application of Heavy Duty Type.

Shape B has the special application of Long Life Type.

Possible to solder any surface from small to large.

How to use the Shape B and examples

Hakko T31-02BC28 Bevel Tip

Hakko T31-02BC28, BEVEL, 2.8mm/60° x 17.6mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

This type has a shape like a cone or column cut at a slant, which allows users to select the cut surface size depending on the workpiece.

It is used for drag soldering and pre-tinning of lead wires.

How to use the Shape BC/C and examples

Difference between BC/C and BCF/CF tip shape

Hakko T31-02BC1 Bevel Tip

Hakko T31-02BC1, BEVEL, 1mm/60° x 14.2mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

This type has a shape like a cone or column cut at a slant, which allows users to select the cut surface size depending on the workpiece.

It is used for drag soldering and pre-tinning of lead wires.

How to use the Shape BC/C and examples

Difference between BC/C and BCF/CF tip shape

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-01WD08 Chisel Tip

Hakko T31-01WD08 Chisel Tip

Hakko T31-01WD08, CHISEL, 0.8 x 6mm, IH, 450°C/840°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Flat-blade screwdriver Shape.

Capable of soldering by applying the tip in 2 ways: line and face.

Width (size of tip) suitable for the workpiece can be selected.

Can be used for any soldering work.

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-01SBL Conical Tip

Hakko T31-01SBL Conical Tip

Hakko T31-01SBL, CONICAL, R0.2×13.7mm, IH, 450°C/840°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Cone or column Shape cut at a slant.

Allows users to select the cut surface size depending on the workpiece.

Used for drag soldering and pre-tinning of lead wires.

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-01KU Knife Tip

Hakko T31-01KU Knife Tip

Hakko T31-01KU KNIFE, 4.8mm/45° x 15mm, IH, 450°C/840°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Shaped like a knife

Capable of soldering by applying the tip in 3 ways: line, face and point

used for soldering at narrow pitches, correction of bridging and drag soldering

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-01JS02 Bent Tip

Hakko T31-01JS02 Bent Tip

Hakko T31-01JS02, BENT, R0.2mm/30° x 1.8mm x6.6mm, IH, 450°C/840°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Bent tip end

Capable of soldering by applying the tip in 2 ways: face and point

Ideal for drag soldering and correction of bridging

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-01JL02 Bent Tip

Hakko T31-01JL02 Bent Tip

Hakko T31-01JL02, BENT, R0.2mm/30° x 7.2mm x 8mm, IH,450°C/840°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Bent tip end

Capable of soldering by applying the tip in 2 ways: face and point

Ideal for drag soldering and correction of bridging

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-01J02 Bent Tip

Hakko T31-01J02 Bent Tip

Hakko T31-01J02, BENT, R0.2mm/30° x 4mm x 11mm, IH, 450°C/840°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Bent tip end

Capable of soldering by applying the tip in 2 ways: face and point

Ideal for drag soldering and correction of bridging

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-01IL Conical Tip

Hakko T31-01IL Conical Tip

Hakko T31-01IL, CONICAL, R0.2×14.7mm, IH, 450°C/840°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Thin conical end

Ultrafine tip which is best suited for soldering at narrow pitches, etc

Ideal for soldering micro components such as 0603, etc. and for repairing high-density-mounting P.W.Bs. such as in cellular phones, etc

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-01I Conical Tip

Hakko T31-01I Conical Tip

Hakko T31-01I, CONICAL, R0.2 x 8.4mm, IH, 450°C/840°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Thin conical end

Ultrafine tip which is best suited for soldering at narrow pitches, etc

Ideal for soldering micro components such as 0603, etc. and for repairing high-density-mounting P.W.Bs. such as in cellular phones, etc

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-01D52 Chisel Tip

Hakko T31-01D52 Chisel Tip

Hakko T31-01D52,CHISEL,5.2 x 7.8mm,IH,450°C/840°F,FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Flat-blade screwdriver Shape

Capable of soldering by applying the tip in 2 ways: line and face

Width (size of tip) suitable for the workpiece can be selected

Can be used for any soldering work.

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-02D24 Chisel Tip

Hakko T31-02D24 Chisel Tip

Hakko T31-02D24, CHISEL, 2.4 x 10mm, IH, 400°C/750°F, FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 750°F (400°C)

This type has a shape like a flat-blade screwdriver and is capable of soldering by applying the tip in 2 ways: line and face.

The width (size of tip) suitable for the workpiece can be selected, and it can be used for any soldering work.

How to use the Shape D and examples

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-01D16 Chisel Tip

Hakko T31-01D16 Chisel Tip

TIP,CHISEL,1.6 x 10mm,IH,450°C/840°F,FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Temperature: 840°F (450°C)

This type has a shape like a flat-blade screwdriver and is capable of soldering by applying the tip in 2 ways: line and face.

The width (size of tip) suitable for the workpiece can be selected, and it can be used for any soldering work.

How to use the Shape D and examples

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31B-01D08 Chisel Tip

Hakko T31-01D08 Chisel Tip

TIP,CHISEL,0.8 x 9mm,IH,450°C/840°F,FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

This type has a shape like a flat-blade screwdriver and is capable of soldering by applying the tip in 2 ways: line and face.

The width (size of tip) suitable for the workpiece can be selected, and it can be used for any soldering work.

How to use the Shape D and examples

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko T31-01BL Conical Tip

Hakko T31-01BL Conical Tip

TIP,CONICAL,R0.2 x 12mm, IH,450°C/840°F,FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

Shape B has the special application of Heavy Duty Type.

Shape B has the special application of Long Life Type.

Possible to solder any surface from small to large.

How to use the Shape B and examples

Hakko T31-01BC28 Bevel Tip

Hakko T31-01BC28 Bevel Tip

TIP,BEVEL,2.8mm/60° x 17.6mm,IH,450°C/840°F,FX-1001

T31 Series Composite Tip

This soldering tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

This type has a shape like a cone or column cut at a slant, which allows users to select the cut surface size depending on the workpiece.

It is used for drag soldering and pre-tinning of lead wires.

How to use the Shape BC/C and examples

Difference between BC/C and BCF/CF tip shape

Hakko T31-01BC1 Bevel Tip

Hakko T31-01BC1 Bevel Tip

TIP,BEVEL,1mm/60° x 14.2mm,IH,450°C/840°F,FX-1001

T31 Series Composite Tip

This tip is used with the Hakko FX-100 Induction Heat Soldering System.

Use with the Hakko FX1001-51 soldering iron.

Temperature: 840°F (450°C)

This type has a shape like a cone or column cut at a slant, which allows users to select the cut surface size depending on the workpiece.

It is used for drag soldering and pre-tinning of lead wires.

How to use the Shape BC/C and examples

Difference between BC/C and BCF/CF tip shape

Kiesub offers a wide range of soldering tip variations.

HAKKO proposes guidelines on how to select the most suitable tip size.

Hakko FX100-04 INDUCTION HEAT SOLDERING SYSTEM

Hakko FX100-04 Induction Heat Soldering System

Raising the world standard in induction heating soldering irons

fx100_5

The FX-100 soldering system brings induction heat soldering technology to an even higher performance level. This small, compact station includes microprocessor control that boost the recovery performance of the soldering iron tip, and an Advanced System Design optimizes performance by reducing the loss of power in the system while maintaining the lowest EMI levels to meet applicable standards, especially for work with sensitive devices.

The unique Induction Heating (IH) system used by the HAKKO FX-100, which automatically heats the tips and rapidly returns it to the fixed temperature whenever a load is applied to the tip, includes HAKKO’s proprietary “Power Assist” function.
This function provides less temperature drop and improved thermal recovery when soldering. And if you need a bit more power for those challenging solder joints, just select “Boost Mode”.

The system is simple to operate — just plug it in and turn it on. No calibration required.

FX-100 features:

• User selectable Power Activity Display providing constant dynamic feedback to the operator about the thermal load on the soldering iron tip

• T31 Series Tip Cartridges provide HAKKO’s renowned tip life with greater power at each of the two temperature selections

• Password Lockout prevents unauthorized system setup changes

• Tip Sleep function reduces tip temperature to preserve tip life and reduce oxidation when the iron is not in use

• Large Backlit Display provides a clear and simple interface with the operator

• User Programmable Profiles for tip and solder selection

• Activity Monitor provide cumulative data on tip heater loads and tip running time to aid in process control and managing operating costs

• Auto-Power Off safety feature

• Compact design minimizes the workbench footprint

• Slender, lightweight, and ergonomically designed handpiece with burn resistant cord allowing for excellent operator dexterity

• Meets or exceeds requirements under IPC J-STD-001, ANSDI ESD S20.20 and older MIL-STDs.

fx100_6

T31 Series tips ordered separately

Model Name	FX100
Part Number	FX100-04
Voltage	120V
Power Consumption	85W
Temperature Stability & Accuracy	Meets or Exceeds UPC J-STD-001
Output Power	50W
Output Frequency	13.56 MHz
Weight	6.6 lb. (3 kg)
Dimensions (W x H x D)	5.0 x 5.9 x 6.6 in. (127 x 150 x 167 mm)

SOLDERING IRON – HANDPIECE

Model Number	FX-1001
Part Number	FX1001-51
Tip-to-Ground Resistance	< 2 ohms
Tip-to-Ground Potential	< 2mV
Length of cord	4.3 ft. (1.3 m)
Total Length (w/o cord)	7.5 in. (190 mm) w/T31-02D24 tip
Weight (w/o cord)	0.07 lb. (31 g) w/T31-02D24 tip
Tips (not included)	T31-01 Series = 840°F (450°C) T31-02 Series = 750°F (400°C)
Reach	4.3 ft. (1.3m)
Heating Element	High Frequency Induction-Type

CONTENTS

Part Number	Description
FX100-04	FX-100 Soldering Station w/ FX-1001 Soldering Iron
FH800-51BY	Iron Holder
B2300	Heat resistant pad
B2419	3-wire Power Cord
B5006	Yellow Soldering Iron Grip (Installed)
B5007	Green Soldering Iron Grip
B5008	Gray Soldering Iron Grip
N/A	Instruction Manual